BS ISO 3408-1:2006
$142.49
Ball screws – Vocabulary and designation
| Published By | Publication Date | Number of Pages |
| BSI | 2006 | 28 |
This part of ISO 3408 establishes the vocabulary for ball screws (see Figure 1) and specifies their designation.
Figure 1 Ball screw
NOTE The actual design need not necessarily correspond to that shown in Figure 1.
Key
Related products
-
BS ISO 128:1982:2000 Edition
Technical drawings. General principles of presentation Published By Publication Date Number of Pages BSI 2000…
-
BS ISO 3408-5:2006
Ball screws – Static and dynamic axial load ratings and operational life Published By Publication…
-
BS EN ISO 6888-3:2003 2006
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of coagulase-positive staphylococci…
-
BS ISO/IEC 15426-1:2000
Information technology. Automatic identification and data capture techniques. Bar code verifier conformance specifications – Linear…
-
BS EN ISO 9917-1:2007
Dentistry. Water-based cements – Powder/liquid acid-base cements Published By Publication Date Number of Pages BSI…
-
BS EN ISO 14660-2:2000
Geometrical product specifications (GPS). Geometrical features – Extracted median line of a cylinder and a…
-
BS ISO 129:1985:2000 Edition
Technical drawings. Dimensioning. General principles, definitions, methods of execution and special indications Published By Publication…
-
BS 308-2:1985
Engineering drawing practice – Recommendations for dimensioning and tolerancing of size Published By Publication Date…
-
BS ISO 1101:1983:2000 Edition
Technical drawings. Geometrical tolerancing. Tolerancing of form, orientation, location and run-out. Generalities, definitions, symbols, indications…
-
BS ISO 3308:2012
Routine analytical cigarette-smoking machine. Definitions and standard conditions Published By Publication Date Number of Pages…
-
BS EN 13824:2004
Sterilization of medical devices. Aseptic processing of liquid medical devices. Requirements Published By Publication Date…
-
BS ISO 11568-2:2005:2006 Edition
Banking. Key management (retail) – Symmetric ciphers, their key management and life cycle Published By…
-
BS ISO 3808:2002 2003
Road vehicles. Unscreened high-voltage ignition cables. General specifications, test methods and requirements Published By Publication…
-
BS ISO 128:1982:2000 Edition
Technical drawings. General principles of presentation Published By Publication Date Number of Pages BSI 2000…
-
BS ISO 1302:1992:2000 Edition
Technical drawings. Method of indicating surface texture Published By Publication Date Number of Pages BSI…
-
BS ISO 13323-1:2000:2002 Edition
Determination of particle size distribution. Single-particle light interaction methods – Light interaction considerations Published By…
-
BS EN ISO 14855-1:2007:2010 Edition
Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions. Method by…
-
BS EN ISO 3405:2000 2001
Methods of test for petroleum and its products. Petroleum products. Determination of distillation characteristics at…
-
BS ISO 6336-1:2006:2008 Edition
Calculation of load capacity of spur and helical gears – Basic principles, introduction and general…
-
BS EN ISO 9917-1:2003:2004 Edition
Dental water-based cements – Powder/liquid acid-base cements Published By Publication Date Number of Pages BSI…
-
BS 5668-1:1992
Routine analytical cigarette smoking machine – Specification and standard conditions Published By Publication Date Number…
-
BS EN ISO 3098-6:2000
Technical product documentation. Lettering. – Cyrillic alphabet Published By Publication Date Number of Pages BSI…
-
BS ISO 3408-3:2006
Ball screws – Acceptance conditions and acceptance tests Published By Publication Date Number of Pages…
-
BS EN ISO 128-20:2001:2002 Edition
Technical drawings. General principles of presentation – Basic conventions for lines Published By Publication Date…
-
BS ISO 7573:1983:2000 Edition
Technical drawings. Item list Published By Publication Date Number of Pages BSI 2000 8
-
BS EN ISO 128-21:2001:2002 Edition
Technical drawings. General principles of presentation – Preparation of lines by CAD systems Published By…
-
BS EN ISO 6888-3:2003 2006
Microbiology of food and animal feeding stuffs. Horizontal method for the enumeration of coagulase-positive staphylococci…
-
BS ISO 3308:2000+A1:2009:2010 Edition
Routine analytical cigarette-smoking machine. Definitions and standard conditions Published By Publication Date Number of Pages…
-
BS 6101-4:1987
Machine tool ball screws – Method of calculation of static axial rigidity Published By Publication…
-
BS EN ISO 3098-3:2000
Technical product documentation. Lettering. – Greek alphabet Published By Publication Date Number of Pages BSI…
-
BS ISO 4308-1:2003
Cranes and lifting appliances. Selection of wire ropes – General Published By Publication Date Number…
-
BS 2782:1970:1987 Edition
Methods of testing plastics Published By Publication Date Number of Pages BSI 1987 46
-
BS ISO 2692:1988:2000 Edition
Technical drawings. Geometrical tolerancing. Maximum material principle Published By Publication Date Number of Pages BSI…
-
BS 308-3:1990
Engineering drawing practice – Recommendations for geometrical tolerancing Published By Publication Date Number of Pages…
-
BS EN ISO 14855:2004
Determination of the ultimate aerobic biodegradability and disintegration of plastic materials under controlled composting conditions.…
-
BS ISO 3438:2003 2004
Subland twist drills with Morse taper shanks for holes prior to tapping screw threads Published…
-
BS ISO 3408-4:2006
Ball screws – Static axial rigidity Published By Publication Date Number of Pages BSI 2006…
-
BS 3406-6:1985
Methods for determination of particle size distribution – Recommendations for centrifugal liquid sedimentation methods for…
-
BS ISO 13318-2:2001:2002 Edition
Determination of particle size distribution by centrifugal liquid sedimentation methods – Photocentrifuge method Published By…
-
BS EN ISO 3405:2011
Petroleum products. Determination of distillation characteristics at atmospheric pressure Published By Publication Date Number of…
