Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 13480-3:2017+A4:2021

BS EN 13480-3:2017+A4:2021

$215.11

Metallic industrial piping – Design and calculation

Published By Publication Date Number of Pages
BSI 2021 456
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
2 undefined
40 1 Modification to Clause 2, “Normative references”
2 Modification to 5.2.4, “Steel castings”
3 Modification to Annex A, “Dynamic effect”
41 Annex A (informative)Dynamic effect
A.1 General
A.1.1 Introduction
A.1.2 Vibration design guidelines
A.1.2.1 General
A.1.2.2 Operation of the circuit
44 A.1.2.3 Equipment
46 A.1.2.4 Layout
47 A.2 Analysis by calculation
A.2.1 General
A.2.2 Seismic events
A.2.2.1 General
A.2.2.2 Simplified static equivalent analysis
48 A.2.2.3 Quasi-static equivalent analysis
49 A.2.2.4 Modal response spectra analysis
50 A.2.2.5 Force time history analysis
51 A.2.2.6 Damping values
52 A.2.2.7 Seismic support displacement
A.2.3 Rapid valve closure
A.2.3.1 General
53 A.2.3.2 Simplified static analysis of rapid valve closure
55 A.2.3.3 Advanced methods of calculation
A.2.4 Flow induced vibration
A.2.4.1 General
56 A.2.4.2 Vortex shedding
57 A.2.4.3 Pump induced fluid pulsing
A.2.4.4 Flow regimes
58 A.2.5 Safety valve discharge
A.2.5.1 General
A.2.5.2 Simple static analysis
60 A.2.6 Allowable stresses
A.2.7 Structural vibration properties
A.2.7.1 General
61 A.2.7.2 Application of DS or MVF
A.2.7.3 Dynamic Susceptibility
A.2.7.4 Modal Vibration Factor
62 A.2.7.5 Error estimation
A.3 Alternative means of design verification
A.3.1 Comparative studies
A.3.2 Full scale testing
63 A.3.3 Reduced scale testing
A.4 Validation (measuring)
4 Modification to Clause G.3, “Physical properties of steels”
5 Introduction of a new Clause G.4, “Material properties of carbon steel at elevated temperatures”
64 6 Introduction of a new Annex R, “Surveillance of components operating in the creep range”
65 Annex R(informative)Surveillance of components operating in the creep range
R.1 General
R.2 Recording of operating data
R.3 Calculation of the creep exhaustion or the theoretical residual lifetime
67 R.4 Assessment of the cumulated creep
R.5 Review and repair of cracks
R.6 Creep and fatigue
R.7 Measures when reaching certain degrees of exhaustion
68 7 Modification to Bibliography
73 1 Modifications to European foreword
2 Modifications to Clause 2, Normative references
3 Modifications to 3.2, Symbols and units
4 Modifications to 4.2.3.4, Calculation pressure
5 Modifications to 4.3, Thickness
6 Modifications to 4.6, Dimensioning of piping components subject to pressure
74 7 Modifications to 5.2.1, Steels other than austenitic steels
8 Modifications to 5.2.4, Steels castings
9 Modifications to 5.2.5.1, General
10 Modifications to 5.3.2.1, Design conditions
75 11 Modifications to 6.2, Pipe bends and elbows
12 Modifications to 6.4.3, Specific symbols and abbreviations
76 13 Modifications to 6.4.10, Special forged reducers
14 Modifications to 6.5.2, Expansion joints
15 Modifications to 6.6, Bolted flange connections
16 Modifications to 6.6.4, Non-standard flange
17 Modifications to 7.1, Dished ends
77 18 Modifications to 7.1.3, Torispherical ends
19 Modifications to 7.2, Circular flat ends
20 Modifications to 7.2.3.3, Unflanged flat ends
21 Modifications to 7.2.4.1, General
78 22 Modifications to 7.2.5.2, Flat ends with openings
23 Modifications to 8.4.1, General
24 Modifications to 8.4.4, Reinforced single openings with 0,8 < d/D ≤ 1,0
25 Modifications to 8.5.2, Reinforced openings with d/D ≤ 0,8
79 26 Modifications to 8.6.1, Cylindrical Y-pieces
27 Modifications to 10.3.2, Simplified fatigue analysis
28 Modifications to 10.3.2.3, Determination of allowable number of load cycles
29 Modifications to 10.4.2, Design guidance
30 Modifications to 11.3, Symbols
31 Modifications to 12.2.3, Displacement strains
32 Modifications to 12.2.5, Stress range
80 33 Modifications to 12.2.7.1, Thermal expansion data
34 Modifications to 12.2.10.2, Formal analysis required
35 Modifications to C.1.3, Design of expansion joints
36 Modifications to D.4.1, Introduction
37 Modifications to D.4.4, Flange construction
38 Modifications to D.4.6, Gaskets
39 Modifications to D.5.2, Bolt loads and areas
81 40 Modifications to D.5.4.2, Stress limits
41 Modifications to E.2.1, Angles and areas
42 Modifications to F.2, Measures to be taken when the calculated fatigue life has been reached
82 43 Modifications to L.2, Symbols
44 Modifications to L.4, Allowable compressive stress
45 Modifications to Annex P, Recommended gaskets for industrial piping
46 Modifications to Q.3, Explanatory notes for Table Q.1
47 Modifications to Bibliography
88 1 Modifications to Clause 2, Normative references
2 Modifications to 13.11, Manufacturing of pipe supports
89 3 Modifications to Annex N, Documentation of supports

Related products

BS EN 13480-3:2017+A4:2021
$215.11