ISO 8737:1986
$13.00
Taper pins with external thread, unhardened
| Published By | Publication Date | Number of Pages |
| ISO | 1986-11 | 5 |
Specifies the characteristics of products with metric dimensions and nominal diameters from 5 mm up to and including 50 mm; tabulates thread sizes M 5 up to M 50 with nominal lengths from 40 mm up to 400 mm and specifications with reference to International Standards; gives an example for the designation.
Related products
-
BS EN 28735:1992:1989 Edition
Parallel pins with internal thread, hardened Published By Publication Date Number of Pages BSI 1989…
-
BS EN ISO 7837:2001
Fertilizers. Determination of bulk density (loose) of fine-grained fertilizers Published By Publication Date Number of…
-
BS 1742-3:1990
Methods for chemical analysis of condensed milks – Determination of fat content Published By Publication…
-
ISO 8732:1988
Banking — Key management (wholesale) Published By Publication Date Number of Pages ISO 1988-11 90
-
ISO 8731-1:1987
Banking — Approved algorithms for message authentication — Part 1: DEA Published By Publication Date…
-
ISO 6702-2:1991
Aircraft — Requirements for on-board weight and balance systems — Part 2: Design, performance and…
-
BS 5551-3-3.3:1984
Fertilizers. Physical properties. – Method for determination of bulk density (loose) of fine-grained fertilizers Published…
-
BS 5389:1976
Method of test for enclosure pressurization systems on agricultural tractors and self-propelled machines Published By…
-
BS 7101:1989
Procedures for protecting authentic wholesale messages between financial institutions Published By Publication Date Number of…
-
ISO 8787:1986
Papier et carton — Détermination de l’ascension capillaire — Méthode de Klemm Published By Publication…
-
BS EN 28733:1992
Parallel pins with internal thread, unhardened Published By Publication Date Number of Pages BSI 1992…
-
ISO 7152:1997
Camping tents and caravan awnings — Vocabulary and list of equivalent terms Published By Publication…
-
BS EN 28739:1992:1989 Edition
Grooved pins. Full-length parallel grooved, with pilot Published By Publication Date Number of Pages BSI…
-
CAN/CSA-Z8638-08:2008 Edition
Cardiovascular Implants and Artificial Organs – Extracorporeal Blood Circuit for Haemodialysers, Haemodiafilters and Haemofilters Published…
-
ISO 5737:1983
Prints — Preparation of standard prints for optical tests Published By Publication Date Number of…
-
BS ISO 8137:1986:1997 Edition
Hydraulic fluid power. Single rod cylinders, 250 bar (25 MPa) series. Port dimensions Published By…
-
CAN/CSA-Z8637-08:2008 Edition
Cardiovascular Implants and Artificial Organs – Haemodialysers, Haemodiafilters, Haemofilters and Haemoconcentrators Published By Publication Date…
-
ISO 8736:1986
Taper pins with internal thread, unhardened Published By Publication Date Number of Pages ISO 1986-11…
-
BS 7011-2.1:1989
Consumable accessories for light microscopes. Slides. – Specification for dimensions and optical properties Published By…
-
BS 7102-2:1989
Recommendations for algorithms for use in banking message authentication. – Message Authenticator Algorithm Published By…
-
BS EN 28736:1992
Taper pins with internal thread, unhardened Published By Publication Date Number of Pages BSI 1992…
-
SAE J 1580:2011
Metric Countersunk Holes for Cutting Edges and End Bits Published By Publication Date Number of…
-
ISO 873:1980
Peaches — Guide to cold storage Published By Publication Date Number of Pages ISO 1980-08…
-
ISO 8037-1:1986
Optique et instruments d’optique — Microscopes — Lames porte-objet — Partie 1: Dimensions, propriétés optiques…
-
ISO 3737:1976
Agricultural tractors and self-propelled machines — Test method for enclosure pressurization systems Published By Publication…
-
BS 7102-1:1989
Recommendations for algorithms for use in banking message authentication – Data Encryption Algorithm (DEA) Published…
-
BS EN ISO 877:1997:1996 Edition
Plastics. Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified…
-
ISO 8137:1986
Hydraulic fluid power — Single rod cylinders, 250 bar (25 MPa) series — Port dimensions…
-
ISO 8738:1986
Plain washers for clevis pins — Product grade A Published By Publication Date Number of…
-
BS EN 28738:1992
Plain washers for clevis pins. Product grade A Published By Publication Date Number of Pages…
-
BS 7308:1990
Method for presentation of dimensional accuracy data in building constructions Published By Publication Date Number…
-
BS ISO 8730:1990
Banking. Requirements for message authentication (wholesale) Published By Publication Date Number of Pages BSI 1990…
-
BS 2782-5 Method 550A:1981
Methods of testing plastics. Optical and colour properties, weathering – Methods of exposure to natural…
-
BS ISO 16609:2004:2006 Edition
Banking. Requirements for message authentication using symmetric techniques Published By Publication Date Number of Pages…
-
BS EN 28747:1992:1989 Edition
Grooved pins with countersunk head Published By Publication Date Number of Pages BSI 1989 13
-
ISO 7737:1986
Tolérances pour le bâtiment — Présentation des données sur l’exactitude dimensionnelle Published By Publication Date…
-
BS EN ISO 8637:2014
Cardiovascular implants and extracorporeal systems. Haemodialysers, haemodiafilters, haemofilters and haemoconcentrators Published By Publication Date Number…
-
BS 2782-5 Method 540A:1977
Methods of testing plastics. Optical and colour properties, weathering – Determination of resistance to change…
-
BS EN 28734:1992:1989 Edition
Parallel pins, hardened (dowel pins) Published By Publication Date Number of Pages BSI 1989 14
-
BS EN 28737:1992
Taper pins with external thread, unhardened Published By Publication Date Number of Pages BSI 1992…