šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN ISO 19085-12:2021+A11:2023

BS EN ISO 19085-12:2021+A11:2023

$198.66

Woodworking machines – Safety – Part 12: Tenoning/profiling machines

Published By Publication Date Number of Pages
BSI 2023 70
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages PDF Title
2 undefined
7 Annex ZA (informative)Relationship between this European Standard and the essential requirements of Directive 2006/42/EC aimed to be covered
12 Foreword
13 Introduction
15 1 Scope
16 2 Normative references
17 3 Terms and definitions
26 4 List of significant hazards
28 5 Safety requirements and measures for controls
5.1 Safety and reliability of control systems
5.2 Control devices
5.2.1 General
5.2.2 Additional requirements for single end tenoning machines with manual feed sliding table
5.2.3 Additional requirements for single end tenoning machines with mechanical feed sliding table
5.2.4 Additional requirements for single end tenoning and/or profiling machines with mechanical feed
29 5.2.5 Additional requirements for double end machines
5.2.6 Additional requirements for angular systems for tenoning and profiling with mechanical feed
5.3 Start
5.3.1 Machines with manual feed
5.3.2 Machines with mechanical feed
30 5.3.3 Laser marking unit
5.4 Safe stops
5.4.1 General
5.4.2 Normal stop
31 5.4.3 Operational stop
5.4.4 Emergency stop
5.5 Braking function of tool spindles
5.6 Mode selection
5.6.1 General
5.6.2 Adjustment mode (MODE 2)
32 5.7 Spindle speed changing
5.7.1 Spindle speed changing by changing belts on the pulleys
5.7.2 Spindle speed changing by incremental speed change motor
5.7.3 Infinitely variable speed by frequency inverter
5.8 Failure of any power supply
5.9 Manual reset control
5.10 Enabling control
5.11 Machine moving parts limited speed monitoring
5.12 Time delay
33 5.13 Tele-service
6 Safety requirements and measures for protection against mechanical hazards
6.1 Stability
6.1.1 Stationary machines
6.1.2 Displaceable machines
6.2 Risk of break-up during operation
34 6.3 Tool holder and tool design
6.3.1 General
6.3.2 Spindle locking
6.3.3 Circular saw blade fixing devices
6.3.4 Flange dimensions for circular saw blades
6.3.5 Spindle rings
35 6.4 Braking
6.4.1 Braking of tool spindle
6.4.2 Maximum run-down time
6.4.3 Brake release
6.5 Safeguards
6.5.1 Fixed guards
6.5.2 Interlocking moveable guards
6.5.3 Hold-to-run control
6.5.4 Two hand control
36 6.5.5 Electro-sensitive protective equipment (ESPE)
6.5.6 Pressure sensitive protective equipment (PSPE)
6.6 Prevention of access to moving parts
6.6.1 General
6.6.2 Guarding of tools
41 6.6.3 Guarding of drives
42 6.6.4 Guarding of shearing and/or crushing zones
47 6.7 Impact hazard
6.8 Clamping devices
6.8.1 Single end tenoning machines with sliding table
6.8.2 Machines other than single end tenoning machines with sliding table
48 6.9 Measures against ejection
6.9.1 General
6.9.2 Guards materials and characteristics
6.9.3 Devices to minimize the possibility or effect of ejection or kickback
50 6.10 Work-piece support and guides
6.10.1 Single end tenoning machines with sliding table
6.10.2 Single end tenoning and/or profiling machines with mechanical feed
51 6.10.3 Double end tenoning and/or profiling machines with mechanical feed
6.10.4 Angular systems for tenoning and profiling with mechanical feed
6.10.5 Work-piece returner
52 7 Safety requirements and measures for protection against other hazards
7.1 Fire
53 7.2 Noise
7.2.1 Noise reduction at the design stage
7.2.2 Noise emission measurement
7.3 Emission of chips and dust
7.4 Electricity
7.4.1 General
7.4.2 Displaceable machines
7.5 Ergonomics and handling
54 7.6 Lighting
7.7 Pneumatics
7.8 Hydraulics
7.9 Electromagnetic compatibility
7.10 Laser
7.11 Static electricity
7.12 Errors of fitting
7.13 Isolation
55 7.14 Maintenance
7.15 Heat
7.16 Substances
8 Information for use
8.1 Warning devices
8.2 Marking
8.2.1 General
8.2.2 Additional markings
56 8.3 Instruction handbook
8.3.1 General
8.3.2 Additional information
58 Annex A (informative) Performance levels required
60 Annex B (normative) Tests for braking function
61 Annex C (normative) Stability test for displaceable machines
62 Annex D (normative) Impact test for guards
63 Annex E (normative) Noise emission measurement for single end profiling machines (not in ISO 7960:1995)
67 Bibliography

Related products

BS EN ISO 19085-12:2021+A11:2023
$198.66