🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 17003:2021

BS EN 17003:2021

$198.66

Road vehicles. Roller brake testers for vehicles of more than 3,5 tons GVW. Safety requirements

Published By Publication Date Number of Pages
BSI 2021 54
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document applies to roller brake testers (brake test benches) that are designed for roadworthiness tests on categories M2, M3, N2, N3, O3 and O4 vehicles (as defined in Regulation (EU) 2018/858) and that might be also used to test M1, N1 categories. This document covers fixed-bed roller brake testers with or without inspection pits and whose chassis are inside or outside the building. This document does not cover mobile roller or plate brake testers. These roller brake testers are used to take measurements for testing and assessing the efficiencies of the brake systems fitted to vehicles in the above-cited vehicle categories. The users of the roller brake tester are all kinds of staff that for any reason operate the roller brake testers (e.g. staff working in public transport, vehicle rental, vehicle maintenance, vehicle repair, training, test laboratories and vehicle inspection sectors …). This document is not applicable to roller brake testers manufactured before the date of its publication.

PDF Catalog

PDF Pages PDF Title
2 undefined
11 1 Scope
2 Normative references
12 3 Terms and definitions
14 4 Safety requirements for the roller brake testers and/or protective/risk reduction measures
4.1 General requirements
4.1.1 General
4.1.2 General features for safety devices
15 4.1.3 Prevention from intrusion or contact with moving parts
4.1.4 Re-engagement after a stop
4.1.5 Safety during maintenance
4.2 Protection around chassis zone
4.2.1 Protection against hazard arising from moving parts
4.2.2 Axle presence detection
4.2.3 Access protection to the chassis via the floor, around wheels and rollers
17 4.2.4 Access protection to the chassis from the inspection pit (if it exists)
4.2.5 Protection on access via the vehicle cabin
18 4.3 Control console
4.3.1 Location
4.3.2 Control devices
4.3.3 Operating mode
4.3.3.1 General
19 4.3.3.2 Normal mode operation
4.3.3.3 Deadman switch mode operation
4.3.3.4 Maintenance–inspection mode operation
4.3.3.5 Calibration mode
20 4.3.4 Motors start-up
4.4 Emergency stop
4.5 Overview of the safety functions
4.6 Electrical equipment
4.6.1 Electrical equipment conformity requirements
21 4.6.2 Electromagnetic compatibility
4.6.2.1 Brake tester immunity
4.6.2.2 Brake tester emissions
4.7 Display of safety related information
4.8 Warning lights
4.9 Noise
22 5 Verification of the safety specifications and/or preventive measures
25 6 Information for use
6.1 General
6.2 General principles for the drafting of instructions for use
6.2.1 Contents of the instructions for use
26 6.2.2 Marking
6.2.3 Installation instructions
28 6.3 Installing, maintaining and dismantling the equipment
6.3.1 Installing, testing and putting into service
6.3.2 Acceptance testing
6.3.3 Maintaining and inspecting the equipment
6.3.4 Dismantling and end-of-life disposal
29 Annex A (informative)Trapping zone
30 Annex B (normative)Definition and protection of the pit hazard zone
B.1 General
B.2 Means of protection
B.2.1 General
B.2.2 Protection by light curtain
33 B.2.3 Protection by a covering
34 B.3 Installation of protection means
B.3.1 Roller brake tester installed over a pit
B.3.2 Roller brake tester installed after the pit
35 B.3.3 Roller brake tester installed before the pit
B.3.4 Installation height of light curtains
37 Annex C (informative)Examples of access protection to the chassis via the floor, around wheels and rollers
C.1 General
C.2 Opto-electronic device
40 Annex D (informative)Determination of PLr
D.1 General
D.2 Axle presence detection function
D.3 Pit presence detection function
D.4 Deadman switch mode selector
D.5 Calibration mode selector
41 D.6 Emergency stop
42 Annex E (normative)Noise and vehicle exhaust emissions
E.1 Noise test code for roller brake tester
E.1.1 Introduction
E.1.2 Determination of the A-weighted emission sound pressure level at workstation(s)
E.1.2.1 Measurement procedure
E.1.2.2 Measurement positions
43 E.1.2.3 Measurement uncertainty
E.1.3 Mounting and operating conditions
E.1.4 Information to be recorded and reported
E.1.4.1 General
E.1.4.2 General data
E.1.4.3 Mounting and operating conditions
E.1.4.4 Standards
44 E.1.4.5 Noise data
E.1.5 Declaration and verification of noise emission values
45 E.2 Exhaust emissions from the tested vehicle
46 Annex F (informative)List of significant hazards
49 Annex ZA (informative) Relationship between this European Standard and the essential requirements of Directive 2006/42/EC aimed to be covered

Related products

BS EN 17003:2021
$198.66