🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 15094:2022

BS EN 15094:2022

$215.11

Safety of machinery. Safety requirements for cold flat rolling mills

Published By Publication Date Number of Pages
BSI 2022 80
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies the general safety requirements for cold rolling mills for flat products as defined in 3.1. This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1). [Figure 1] This document does not cover: — Design and construction of buildings including cellars and their facilities; — Thermo process equipment, e.g. in accordance with EN 746 series; — Strip processing lines according to EN 15061, e.g. pickling line; — Abrasive blasting plants according to EN 1248; — Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles; — Roll shop equipment; — Hook conveyors according to EN 619; — Non-fixed load lifting attachments, e.g. according to EN 13155; — Storage equipment (e.g. high-bay warehouses); — Cranes, fork lifts, trucks and railway trucks and other vehicles; — Process technology (e.g. systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air); — Firefighting system. NOTE 1 Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.

PDF Catalog

PDF Pages PDF Title
2 National foreword
6 European foreword
7 Introduction
8 1 Scope
9 2 Normative references
11 3 Terms and definitions
16 4 Significant hazards and risk assessment
4.1 General
4.2 Interfaces to the linked/integrated equipment
17 5 Safety requirements and/or protective/risk reduction measures
5.1 General
5.2 General requirements for design, planning and risk assessment
5.2.1 General
18 5.2.2 Planning of rolling mills
5.2.3 Linked equipment
19 5.2.4 Structural assembly
5.2.5 Safety layout
5.2.6 Safety signs and warning devices
20 5.2.7 Personal protective equipment (PPE)
5.2.8 Loss of energy and failure of controls
5.2.9 Workstations and assigned modes of operation
21 5.2.10 Enabling control device and hold-to-run control device
22 5.2.11 Access to and presence in danger zones
25 5.2.12 Safeguarding
5.2.13 Guards
5.2.14 Sensitive protective equipment
26 5.2.15 Guard-rails
5.2.16 Preconditions for movements of equipment not causing significant hazards
5.2.17 Determination of required Performance Level (PLr)
27 5.2.18 Stored energy
28 5.2.19 Mechanical restraint devices
5.2.20 Electrical equipment
5.2.21 Safety-related control systems
5.2.22 Safety-related software and parameters
29 5.2.23 Remote access to the control systems
5.2.24 Radiation and fields
30 5.2.25 Fluid systems (hydraulic, pneumatic, cooling, lubrication and additional media systems)
31 5.2.26 Substances
5.2.27 Firefighting
5.2.28 Ergonomics
32 5.2.29 Vibrations
5.2.30 Noise reduction as a safety requirement
34 5.3 Significant hazards, hazardous situations, safety requirements and/or protective/risk reduction measures
5.3.1 Structure and content of Table 4
51 6 Verification/validation of safety requirements/functions and/or protective/risk reduction measures
6.1 General
52 6.2 Required verification D
6.3 Required verification V, M and T
53 7 Information for use
7.1 General
7.2 Warning devices and safety signs
7.3 Minimum marking
54 7.4 Accompanying documents
7.4.1 Instructions
56 7.4.2 Information for transportation and assembly of the equipment
7.4.3 Information about disabling, disassembly and disposal of the equipment
7.5 Training of personnel
57 8 Supplementary information regarding repair work
58 Annex A (normative) Requirements for shut-down, emergency stop and other stop functions
63 Annex B (normative) Noise test code
68 Annex C (normative) Protection of persons in case of using asphyxiant gases used infirefighting systems
72 Annex D (informative) Machines and/or equipment covered by this document
74 Annex E (informative) Roll spalling
75 Annex F (informative) Example for modes of operation in relation to segregated areas
76 Annex G (informative) Example for the risk analysis due to interfaces
77 Bibliography

Related products

BS EN 15094:2022
$215.11