šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN 1366-4:2021 – TC:2022 Edition

BS EN 1366-4:2021 – TC:2022 Edition

$258.95

Tracked Changes. Fire resistance tests for service installations – Linear joint seals

Published By Publication Date Number of Pages
BSI 2022 142
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

This part of the EN 1366 series specifies a method for determining the fire resistance of linear joint seals based on their intended end use. Perimeter seals of curtain walling are excluded from this part of the EN 1366 series.

This document is intended to be used in conjunction with EN 1363?1.

The following tests are included in this document:

  1. no mechanically induced movement;

  2. mechanically induced movement.

Tests in accordance with this part of the EN 1366 series are not intended to provide quantitative information on the rate of leakage of smoke and/or hot gases, or on the transmission or generation of fumes. Such phenomena are only noted in the test report in describing the general behaviour of test specimens during the test.

The load-bearing capacity of a linear joint seal is not addressed in this part of the EN 1366 series. No information can be implied by the test concerning the influence of the inclusion of linear joint seals on the loadbearing capacity of the separating element.

PDF Catalog

PDF Pages PDF Title
1 30450591
79 A-30394112
80 undefined
87 1 Scope
2 Normative references
3 Terms and definitions
88 4 Test equipment
89 5 Test conditions
5.1 Heating conditions
5.2 Pressure conditions
6 Test specimen
6.1 General
6.2 Size
6.3 Number of test specimens
90 7 Installation of test specimen
7.1 General
7.2 Requirements for specific seal types
7.2.1 Seals made of fabrics
7.2.2 Seals made of foams (foamed in situ)
91 7.2.3 Membrane forming seals
7.2.4 Seals made of mineral wool (faced/coated or not faced/coated)
92 7.2.5 Linear joint seal made of mortar/plaster
93 7.2.6 Linear joint seal made of sealants
7.2.7 Linear joint seal made of pre-formed compressible strips
94 7.2.8 Linear joint seals made of pre-formed compressible composite strips
95 7.2.9 Linear joint seal made of pre-formed compressible ropes
7.2.10 Linear joint seal made of pre-formed strips
96 7.3 Supporting construction
7.3.1 General
98 7.3.2 Standard supporting construction
7.3.2.1 Wall constructions
7.3.2.2 Floor constructions
99 7.3.2.3 Steel joint faces
101 7.4 Test construction
104 7.5 Splice locations
7.6 Induced movement
8 Conditioning
9 Application of instrumentation
9.1 General
9.2 Thermocouples
9.2.1 Furnace thermocouples
9.2.2 Unexposed face thermocouples
116 9.3 Roving thermocouple
9.4 Deformation and deflection
117 9.5 Integrity measurement
10 Test procedure
10.1 General
10.2 Installation of test construction
10.3 Mechanically induced movement of the test specimen
10.4 Measurements and observations
11 Performance criteria
11.1 Insulation
11.2 Integrity
118 11.3 Expression of results
12 Test report
13 Field of direct application of test results
13.1 Orientation
119 13.2 Supporting construction
13.2.1 Rigid constructions
121 13.2.2 Flexible wall constructions
13.2.3 Flexible floor constructions
13.2.4 Non-standard supporting constructions
13.3 Seal position
13.4 Mechanically induced movement
122 13.5 Dimensions
13.5.1 Linear joint seal made of fabrics
13.5.2 Linear joint seal made of foams ā€“ foamed in situ
13.5.3 Membrane forming seals
13.5.4 Linear joint seal made of mineral wool (faced/coated or not faced/coated)
13.5.5 Linear joint seal made of mortar/plaster
13.5.6 Linear joint seal made of sealants
123 13.5.7 Linear joint seal made of pre-formed compressible strips
124 13.5.8 Linear joint seals made of pre-formed compressible composite strips
13.5.9 Linear joint seal made of pre-formed compressible ropes
125 13.5.10 Linear joint seal made of pre-formed strips
126 Annex A (normative)Standard condition for linear joint seals with no mechanically induced movement of the joint faces
A.1 Standard condition
A.2 Test procedure
127 Annex B (normative)Standard condition for linear joint seals with mechanically induced movement of the joint faces
B.1 General
B.2 Standard condition(s)
B.2.1 Standard condition for lateral movement
129 B.2.2 Standard condition for shear movement
130 B.2.3 Standard condition for a combination of lateral and shear movement
132 Annex C (informative)Guidance on the use of this document
C.1 General
C.2 Application of the test
C.3 Test conditions
133 C.4 Specimen preparation
C.5 Notes on general performance criteria
C.6 Notes on validity of test results
134 C.7 Notes on Annex B

Related products

BS EN 1366-4:2021 - TC
$258.95