ASTM-F2707 2010
$35.75
F2707-10 Standard Safety Performance Specification for Safe Design and Installation of Field Fabricated Suction-Limiting Vent Systems for Suction Entrapment Prevention in Swimming Pools, Spas, Hot Tubs, and Wading Pools
| Published By | Publication Date | Number of Pages |
| ASTM | 2010 | 4 |
1.1 This safety performance specification provides requirements for safety in design and installation when using a suction-limiting vent system for suction entrapment prevention in swimming pools, spas, hot tubs, or wading pools.
1.2 The purpose of the vent is to relieve the vacuum at the suction outlet(s) caused by any blockage of the suction outlet(s). The vent is intended to prevent body entrapment at the suction outlet(s) and may also mitigate limb entrapment. It is not intended to prevent other injuries caused by the suction outlet(s) such as hair entrapment, mechanical entrapment, or evisceration.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Scope Referenced Documents Terminology Significance and Use General Requirements |
| 2 | Specific Requirements Field Testing TABLE 1 |
| 3 | Site Signage FIG. 1 |
| 4 | Vent Fitting Signage Keywords A1. BASIS OF TABLE 1 A1.1 |
Related products
-
ASTM-F2777 2016
F2777-16 Standard Test Method for Evaluating Knee Bearing (Tibial Insert) Endurance and Deformation Under High…
-
ASTM-F2757 2020
F2757-20 Standard Guide for Home Laundering Care and Maintenance of Flame Resistant or Arc Rated…
-
ASTM-F2007 2000
F2007-00 Standard Practice for the Classification, Design, Manufacture, and Operation of Concession Go-Karts and Facilities…
-
ASTM-F2807 2013
F2807-13 Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications Published By Publication…
-
ASTM-F2907 2013
F2907-13a Consumer Safety Specification for Sling Carriers Published By Publication Date Number of Pages ASTM…
-
ASTM-F2807 2018
F2807-13(2018) Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications Published By Publication…
-
ASTM-F2737 2010
F2737-10 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units Published By Publication…
-
ASTM-F2706 2018
F2706-18 Standard Test Methods for Occipital-Cervical and Occipital-Cervical-Thoracic Spinal Implant Constructs in a Vertebrectomy Model…
-
ASTM-F2787 2011(Redline)
F2787-11 Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers (Redline) Published…
-
ASTM-F2702 2015(Redline)
F2702-15 Standard Test Method for Radiant Heat Performance of Flame Resistant Clothing Materials with Burn…
-
ASTM-F2507 2010
F2507-05(2010) Standard Specification for Recreational Airpark Design Published By Publication Date Number of Pages ASTM…
-
ASTM-E2707 2015
E2707-15 Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct…
-
ASTM-F2907 2013(Redline)
F2907-13b Standard Consumer Safety Specification for Sling Carriers (Redline) Published By Publication Date Number of…
-
ASTM-F2747 2019
F2747-19 Standard Guide for Construction of Sand-based Rootzones for Golf Putting Greens and Tees Published…
-
ASTM-F2907 2015
F2907-15 Standard Consumer Safety Specification for Sling Carriers Published By Publication Date Number of Pages…
-
ASTM-F2706 2018(Redline)
F2706-18 Standard Test Methods for Occipital-Cervical and Occipital-Cervical-Thoracic Spinal Implant Constructs in a Vertebrectomy Model…
-
ASTM-F2709 2018
F2709-18 Standard Test Method for Determining a Measured Nameplate Recovery Rate of Stationary Oil Skimmer…
-
ASTM-F2787 2013
F2787-13 Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers Published By…
-
ASTM-F2737 2011(Redline)
F2737-11 Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units (Redline) Published By…
-
ASTM-F2777 2010
F2777-10 Standard Test Method for Evaluating Knee Bearing (Tibial Insert) Endurance and Deformation Under High…
-
ASTM-F2706 2017(Redline)
F2706-17 Standard Test Methods for Occipital-Cervical and Occipital-Cervical-Thoracic Spinal Implant Constructs in a Vertebrectomy Model…
-
ASTM-F2757 2016
F2757-09(2016) Standard Guide for Home Laundering Care and Maintenance of Flame, Thermal and Arc Resistant…
-
ASTM-F2797 2010
F2797-10 Standard Test Method for Evaluating Edge Cleaning Effectiveness of Vacuum Cleaners Published By Publication…
-
ASTM-F2787 2018
F2787-13(2018) Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers Published By…
-
ASTM-F2737 2010
F2737-10a Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units Published By Publication…
-
ASTM-F2767 2012
F2767-12 Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and…
-
ASTM-F2703 2013
F2703-08(2013) Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing…
-
ASTM-F2727 2020
F2727-09(2020) Standard Guide for Manufacturers for Labeling Headgear Products Published By Publication Date Number of…
-
ASTM-F2907 2014
F2907-14a Standard Consumer Safety Specification for Sling Carriers Published By Publication Date Number of Pages…
-
ASTM-F2207 2019
F2207-06(2019) Standard Specification for Cured-in-Place Pipe Lining System for Rehabilitation of Metallic Gas Pipe Published…
-
ASTM-F2077 2018(Redline)
F2077-18 Test Methods For Intervertebral Body Fusion Devices (Redline) Published By Publication Date Number of…
-
ASTM-F2700 2013
F2700-08(2013) Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing…
-
ASTM-F2707 2018
F2707-10(2018)e1 Standard Safety Performance Specification for Safe Design and Installation of Field Fabricated Suction-Limiting Vent…
-
ASTM-F2747 2010
F2747-10 Standard Guide for Construction of Sand-based Rootzones for Golf Putting Greens and Tees Published…
-
ASTM-F2407 2020(Redline)
F2407-20 Standard Specification for Surgical Gowns Intended for Use in Healthcare Facilities (Redline) Published By…
-
ASTM-F2757 2020(Redline)
F2757-20 Standard Guide for Home Laundering Care and Maintenance of Flame Resistant or Arc Rated…
-
ASTM-F2700 2020
F2700-08(2020) Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame-Resistant Materials for Clothing with…
-
ASTM-F2907 2014(Redline)
F2907-14b Standard Consumer Safety Specification for Sling Carriers (Redline) Published By Publication Date Number of…
-
ASTM-F2727 2014
F2727-09(2014) Standard Guide for Manufacturers for Labeling Headgear Products Published By Publication Date Number of…
-
ASTM-F2704 2010
F2704-10 Standard Specification for Air-Fed Protective Ensembles Published By Publication Date Number of Pages ASTM…
