ASTM-D6987 2011(Redline)

$38.35

D6987/D6987M-11 Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Redline)

Published By	Publication Date	Number of Pages
ASTM	2011	39

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Significance and Use

This test method was developed to evaluate the wear performance of engine oils in turbocharged and intercooled four-cycle diesel engines equipped with EGR. Obtain results from used oil analysis and component measurements before and after the test.

The test method may be used for engine oil specification acceptance when all details of the procedure are followed.

1. Scope

1.1 This test method is commonly referred to as the Mack T-10. This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including lead corrosion and wear of piston rings and cylinder liners.

1.2 This test method also provides the procedure for running an abbreviated length test, which is commonly referred to as the T-10A. The procedures for the T-10 and T-10A are identical with the exception of the items specifically listed in Annex A8. Additionally, the procedure modifications listed in Annex A8 refer to the corresponding section of the T-10 procedure.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A7 for specific Safety Hazards.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D86 Test Method for Distillation of Petroleum Products at Atmospheric Pressure D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester D97 Test Method for Pour Point of Petroleum Products D129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test D235 Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) D287 Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method) D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) D482 Test Method for Ash from Petroleum Products D524 Test Method for Ramsbottom Carbon Residue of Petroleum Products D613 Test Method for Cetane Number of Diesel Fuel Oil D664 Test Method for Acid Number of Petroleum Products by Potentiometric Titration D976 Test Method for Calculated Cetane Index of Distillate Fuels D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption D2274 Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method) D2500 Test Method for Cloud Point of Petroleum Products D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry D2709 Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge D3338 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter D4485 Specification for Performance of Active API Service Category Engine Oils D4739 Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration D5185 Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) D5186 Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography D5302 Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions D5844 Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID) D5967 Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine D6078 Test Method for Evaluating Lubricity of D

Additional information

Standard Title	D6987/D6987M-11 Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Redline)
Published Code	ASTM
Publication Date	2011
Pages Count	39

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D6987 2011(Redline)

Related products