Shopping Cart

No products in the cart.

ASTM-B150:2008 Edition(Redline)

$26.65

B150/B150M-08 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes (Redline)

Published By Publication Date Number of Pages
ASTM 2008 10
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

Abstract

This specification establishes the requirements for rods, bars, and shapes of aluminum bronze with Copper Alloy UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210. Products shall be produced in tempers HR50, M10, M20, M30, O20, O25, O30, O32, TQ30, TQ50 and TQ55. Products shall be tested and shall conform to dimensional (mass, diameter, length, thickness, straightness, and edge contour), mechanical (tensile and yield strength, Rockwell hardness, and elongation), and chemical composition requirements. Products should also meet requirements under mercurous nitrate test, ammonia test, and piston finish.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210.

Note 1ā€”Product intended for hot forging is described in Specification B 124/B 124M.

Note 2ā€” Warning ā€” Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA ā€™ s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.

1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes B154 Test Method for Mercurous Nitrate Test for Copper Alloys B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings B601 Classification for Temper Designations for Copper and Copper Alloys–Wrought and Cast B858 Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys E8 Test Methods for Tension Testing of Metallic Materials E8M Test Methods for Tension Testing of Metallic Materials [Metric] E18 Test Methods for Rockwell Hardness of Metallic Materials E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) E118 Test Methods for Chemical Analysis

ASTM-B150
$26.65