| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 8<\/td>\n | Foreword <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Introduction <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 1 Scope <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 2 Normative references 3 Terms, definitions, abbreviated terms, and acronyms <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 4 General requirements 4.1 V-model 4.2 Voltages 4.3 Environmental and operational requirements <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 4.4 Components and devices 5 Protection against electric shock hazards 5.1 General 5.1.1 Fundamental requirements 5.1.2 Determination of shock protection requirements <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 5.2 Protective measures <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 5.3 Basic protection 5.3.1 General 5.3.2 Basic insulation 5.3.3 Enclosures or barriers <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 5.3.4 Limitation of touch current and charge 5.3.5 Limitation of voltage 5.4 Fault protection 5.4.1 General <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 5.4.2 PEPB <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | 5.4.3 Automatic disconnection of power supply 5.4.4 Supplementary insulation 5.4.5 Basic protection between circuits 5.5 Enhanced protection 5.5.1 General <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | 5.5.2 Reinforced insulation and protective separation between circuit 5.5.3 Protection by means of protective impedance and limited available charge <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | 5.6 Equipment protective combinations <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | 5.7 Separation of VC-A2- and VC-B1-systems from VC-B2 (and higher) systems 5.8 Protection against residual voltages 5.8.1 Basic 5.8.2 Protection by power source disruption <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | 5.9 Connector human contact 5.9.1 General 5.9.2 Mated non-enclosed connectors 5.9.3 Non-mated, non-enclosed connectors <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | 5.9.4 Enclosed connectors 5.9.5 Tractor implement plug\/socket combinations (or similar mobile machinery implement and attachment combinations) 5.10 Water depth <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | 6 Wiring practices 6.1 Conductor and cable runs 6.2 Colour 6.3 Cable routing 6.4 Power supply voltage differences <\/td>\n<\/tr>\n | ||||||
| 36<\/td>\n | 7 Overcurrent protection (OCP) 7.1 General 7.1.1 Transformers 7.1.2 Power converters 7.1.3 OCP implementation 7.1.4 Rating and setting of OCP <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | 7.1.5 Placement of OCP 7.1.6 Protection via engine shutoff 7.2 Chassis faults\/residual currents 8 Disconnection and connection 8.1 General 8.1.1 VC-B1 <\/td>\n<\/tr>\n | ||||||
| 38<\/td>\n | 8.1.2 Power converter disconnects 8.1.3 Manually actuated disconnecting devices 8.1.4 Disconnecting multiple power sources <\/td>\n<\/tr>\n | ||||||
| 39<\/td>\n | 8.2 Prevention of unintended start-up 8.3 Charging sources and recuperation 8.3.1 Electrical sources <\/td>\n<\/tr>\n | ||||||
| 40<\/td>\n | 8.3.2 Towed 8.3.3 PTO 8.4 Pre-charge protective measures 9 Connectors 9.1 General 9.1.1 Negative connectors and terminals <\/td>\n<\/tr>\n | ||||||
| 41<\/td>\n | 9.2 Connector mating 9.2.1 Incompletely mated connectors 9.2.2 Connecting and disconnecting under load 9.3 Power cable connections <\/td>\n<\/tr>\n | ||||||
| 42<\/td>\n | 9.4 Terminals for the PEPB cables 9.5 Plug\/socket combination <\/td>\n<\/tr>\n | ||||||
| 43<\/td>\n | 10 Electric motors and generators 10.1 General 10.2 Enclosures 10.3 Mounting and compartments 10.4 Overheating protection <\/td>\n<\/tr>\n | ||||||
| 44<\/td>\n | 10.5 Overspeed protection 10.6 Towing and coasting 10.7 Bonding 10.7.1 Motors and generators 10.7.2 Exempted from marking requirement <\/td>\n<\/tr>\n | ||||||
| 45<\/td>\n | 11 Non-motor loads (components) 11.1 General 11.2 Accessories 12 Insulation coordination 12.1 General 12.2 Cable insulation 12.2.1 Temperature and loading <\/td>\n<\/tr>\n | ||||||
| 46<\/td>\n | 12.2.2 Inspection 12.2.3 Shielding 12.2.4 Different Voltages 13 Verification and validation 13.1 General 14 Information for use 14.1 General <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | 14.2 Markings 14.2.1 First responder information 14.2.2 Shock hazard symbols 14.2.3 Operating voltage 14.2.4 Live parts accessible during installation and maintenance 14.2.5 Bonding 14.2.6 Residual voltage 14.2.7 Power supply disruption <\/td>\n<\/tr>\n | ||||||
| 48<\/td>\n | 14.2.8 Disconnected plug\/socket combinations 14.2.9 Maximum water depth 14.2.10 Connection markings 14.2.11 Conductor and cable colour markings 14.2.12 Bolted joints 14.2.13 Disconnection of electrical sources 14.2.14 Multiple disconnects 14.2.15 Unintended start-up 14.2.16 External charging <\/td>\n<\/tr>\n | ||||||
| 49<\/td>\n | 14.2.17 Towing 14.2.18 Connecting and disconnecting under load 14.2.19 Phase cable connections 14.2.20 Bonding of motors and generators EPB 14.2.21 Shipping, dealer setup, and transport 14.2.22 Electrical ratings <\/td>\n<\/tr>\n | ||||||
| 50<\/td>\n | 14.2.23 Protection systems 14.2.24 General purpose socket-outlets 14.2.25 Magnetic hazard symbols 14.3 Manuals and technical documentation 14.3.1 General 14.3.2 Operator\u2019s manual <\/td>\n<\/tr>\n | ||||||
| 51<\/td>\n | 14.3.3 Service manuals <\/td>\n<\/tr>\n | ||||||
| 53<\/td>\n | Annex\u20acA (Informative) List of significant hazards <\/td>\n<\/tr>\n | ||||||
| 54<\/td>\n | Annex\u20acB (Informative) V-Model <\/td>\n<\/tr>\n | ||||||
| 55<\/td>\n | Annex\u20acC (Informative) Shock protection requirements <\/td>\n<\/tr>\n | ||||||
| 58<\/td>\n | Annex\u20acD (Informative) Protection Classes <\/td>\n<\/tr>\n | ||||||
| 60<\/td>\n | Annex\u20acE (Informative) Documentation <\/td>\n<\/tr>\n | ||||||
| 62<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Draft BS ISO 23285 Agricultural machinery, tractors, and earthmoving machinery. Safety of electrical and electronic components and systems operating at 32 to 75 VDC and 21 to 50 VAC<\/b><\/p>\n |