This part of IEC 62196 applies to EV plugs, EV socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. These accessories have a nominal rated operating voltage not exceeding 480 V AC, 50 Hz to 60 Hz, and a rated current not exceeding 63 A three phase or 70 A single phase, for use in conductive charging of electric vehicles. This document covers the basic interface accessories for vehicle supply as specified in IEC 62196-1. NOTE 1 The term “Electric road vehicles (EV)” comprises all road vehicles, including plug-in hybrid road vehicles (PHEV) that derive all or part of their energy from the rechargeable energy storage systems (RESS). These accessories are intended to be used for circuits specified in IEC 61851-1:2017, which operate at different voltages and frequencies, and which can include extra-low voltage (ELV) and communication signals. The use of these accessories for bidirectional power transfer is under consideration. This document applies to accessories to be used in an ambient temperature between -30 \u00b0C and +40 \u00b0C. NOTE 2 In the following country, other requirements regarding the lower temperature may apply: NO. NOTE 3 In the following country, \u221235 \u00b0C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. Vehicle inlets and vehicle connectors described in this document are intended to be used for charging in modes 1, 2 and 3, cases B and C. The EV socket-outlets and EV plugs covered by this document are intended to be used for charging mode 3 only, case A and B. The modes and permissible connections are specified in IEC 61851-1:2017.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Annex ZA (normative)Normative references to international publicationswith their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | Blank Page <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | FOREWORD <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | INTRODUCTION <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 3 Terms and definitions 4 General 5 Ratings 5.1 Preferred rated operating voltage ranges 5.2 Preferred rated currents 6 Connection between the power supply and the electric vehicle <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 6.1 Interfaces 6.2 Basic interface <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 6.3 DC Interface 6.4 Combined interface Tables Table 201 \u2013 Overview of the basic vehicle interface,configuration type 1, single phase Table 202 \u2013 Overview of the basic vehicle interface,configuration types 2 and 3, three phase or single phase <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 7 Classification of accessories 8 Marking 9 Dimensions <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 10 Protection against electric shock 11 Size and colour of protective earthing and neutral conductors 12 Provisions for earthing Table 203 \u2013 Configuration types and standard sheets <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 13 Terminals 14 Interlocks 15 Resistance to ageing of rubber and thermoplastic material 16 General construction 17 Construction of EV socket-outlets \u2013 General 18 Construction of EV plugs and vehicle connectors 19 Construction of vehicle inlets 20 Degrees of protection 21 Insulation resistance and dielectric strength 22 Breaking capacity <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 23 Normal operation 24 Temperature rise 25 Flexible cables and their connection 26 Mechanical strength 27 Screws, current-carrying parts and connections 28 Creepage distances, clearances and distances through sealing compound 29 Resistance to heat and to fire 30 Corrosion and resistance to rusting 31 Conditional short-circuit current 32 Electromagnetic compatibility (EMC) <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 33 Vehicle drive over 34 Thermal cycling 35 Humidity exposure 36 Misalignment 37 Contact endurance test 201 Resistor coding <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | STANDARD SHEETS CONFIGURATION TYPE 1 <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | CONFIGURATION TYPE 2 Table 204 \u2013 Interoperation of configuration type 2 accessories <\/td>\n<\/tr>\n | ||||||
| 47<\/td>\n | CONFIGURATION TYPE 3 <\/td>\n<\/tr>\n | ||||||
| 66<\/td>\n | Annex A (informative)Legacy drawings from IEC 62196-2:2016 <\/td>\n<\/tr>\n | ||||||
| 71<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles – Dimensional compatibility requirements for AC pin and contact-tube accessories<\/b><\/p>\n |