This International Standard specifies the safety and interchangeability requirements, together with the test methods and conditions, required to show compliance of LED lamps with integrated means for stable operation, intended for domestic and similar general lighting purposes, having:<\/p>\n
a rated power up to 60 W<\/p>\n<\/li>\n
a rated voltage equal to or less than 50 V a.c. r.m.s. or equal or less 120 V ripple free d.c.,<\/p>\n<\/li>\n
caps according to Table 1.<\/p>\n<\/li>\n<\/ul>\n
\nNOTE 1 The value of 60 W rated power is under consideration. Heat management may require lower power.<\/p>\n<\/blockquote>\n
This standard shall be used for products in conjunction with ELV lighting installations.<\/p>\n
With reference to IEC 60364-7-715, in ELV lighting installations only SELV sources are applied. Where bare conductors are used, the maximum lamp voltage shall be 25 V a.c. or 60 V d.c.<\/p>\n
The requirements of this standard relate only to type testing.<\/p>\n
For lamps > 25 V a.c. or 60 V d.c., recommendations for whole production testing or batch testing are given in IEC 60598-1 Table Q.1, column class III luminaire, column 4 or 5.<\/p>\n
\nNOTE 2 Where in this standard the term \u201clamp(s)\u201d is used, it is understood to stand for semi-integrated LED lamp(s) with supply voltages as in the scope above, except where it is obviously assigned to other types of lamps.<\/p>\n<\/blockquote>\n
An overview of systems composed of LED modules, lamps and controlgear is given in IEC 62504. Supply voltage does not mean necessarily mains voltage, e.g. 230 V \/ 50 Hz. A semi-integrated LED lamp can also be driven on a supply voltage with 12 V a.c. or d.c. The control unit in the controlgear in a semi-integrated LED lamp then provides the conversion of 12 V a.c. or d.c. to a special current and voltage to power the LED inside the semi-integrated LED lamp. Schematically, the types of LEDni and LEDsi lamps are shown in Figure 1.<\/p>\n
Figure 1<\/b> Types of LED lamps with supply voltage \u2264 50V<\/p>\n
\nNOTE Figure 1a) type is not covered by this standard.<\/p>\n<\/blockquote>\n
PDF Catalog<\/h4>\n
\n
\n PDF Pages<\/th>\n PDF Title<\/th>\n<\/tr>\n \n 2<\/td>\n undefined <\/td>\n<\/tr>\n \n 4<\/td>\n European foreword
Endorsement notice <\/td>\n<\/tr>\n\n 5<\/td>\n Annex ZA (normative) Normative references to international publications with their corresponding European publications <\/td>\n<\/tr>\n \n 7<\/td>\n English
CONTENTS <\/td>\n<\/tr>\n\n 8<\/td>\n FOREWORD <\/td>\n<\/tr>\n \n 10<\/td>\n INTRODUCTION <\/td>\n<\/tr>\n \n 11<\/td>\n 1 Scope <\/td>\n<\/tr>\n \n 12<\/td>\n 2 Normative references
Figures
Figure 1 \u2013 Types of LED lamps with supply voltage \u2264 50V <\/td>\n<\/tr>\n\n 13<\/td>\n 3 Terms and definitions
4 General requirement and general test requirements
5 Marking <\/td>\n<\/tr>\n\n 14<\/td>\n 6 Interchangeability
6.1 Cap interchangeability
6.2 Bending moment and mass imparted by the lamp at the lampholder
Figure 2 \u2013 Lamp not suitable for use under moisture
Tables
Table 1 \u2013 Interchangeability gauges, lamp cap dimensions, bending moment and mass <\/td>\n<\/tr>\n\n 15<\/td>\n 7 Protection against accidental contact with live parts
8 Insulation resistance and electric strength after humidity treatment
8.1 General
8.2 Insulation resistance
8.3 Electric strength <\/td>\n<\/tr>\n\n 16<\/td>\n 9 Mechanical strength
9.1 Pull force
10 Cap temperature rise
11 Resistance to heat
12 Resistance to flame and ignition
13 Fault conditions
13.1 General
13.2 Compliance
14 Creepage distances and clearances
15 Abnormal operation
Table 2 \u2013 Test voltages for caps <\/td>\n<\/tr>\n\n 17<\/td>\n 16 Photobiological safety
16.1 UV radiation
16.2 Blue light hazard
16.3 Infrared radiation
17 Ingress protection
18 Information for luminaire design <\/td>\n<\/tr>\n\n 18<\/td>\n Annex A (informative) Information for luminaire design
A.1 Water contact
A.2 Further impact on luminaires <\/td>\n<\/tr>\n\n 19<\/td>\n Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. Safety specifications<\/b><\/p>\n
\n\n
\n Published By<\/td>\n Publication Date<\/td>\n Number of Pages<\/td>\n<\/tr>\n \n BSI<\/b><\/a><\/td>\n 2018<\/td>\n 20<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":226862,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[520,2641],"product_tag":[],"class_list":{"0":"post-226860","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-29-140-01","7":"product_cat-bsi","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/226860","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/226862"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=226860"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=226860"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=226860"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}