ISO 16030:2001
$27.95
Pneumatic fluid power — Connections — Ports and stud ends
| Published By | Publication Date | Number of Pages |
| ISO | 2001-12 | 20 |
This International Standard specifies dimensions and performance requirements for ports and stud ends with
parallel threads for pneumatic fluid power applications.
It specifies reusable, positively retained seals for leak-free connections, for use at pressures from ? 0,09 MPa
(? 0,9 bar 1)) up to 1,6 MPa (16 bar).
Only this International Standard is applicable for threaded ports and stud ends specified in new designs in
pneumatic fluid power applications.
Ports and stud ends conforming to this International Standard are not intended to connect with ports and stud ends
that conform to ISO 1179 or threads that conform to ISO 7-1.
Related products
-
ISO 16000-10:2006
Indoor air — Part 10: Determination of the emission of volatile organic compounds from building…
-
ISO 16050:2003
Foodstuffs — Determination of aflatoxin B1, and the total content of aflatoxins B1, B2, G1…
-
ISO 16000-16:2008
Air intérieur — Partie 16: Détection et dénombrement des moisissures — Échantillonnage par filtration Published…
-
ISO 16000-4:2011
Indoor air — Part 4: Determination of formaldehyde — Diffusive sampling method Published By Publication…
-
ISO/TS 16630:2003
Metallic materials — Method of hole expanding test Published By Publication Date Number of Pages…
-
ISO 16037:2002/Amd 1:2011
Rubber condoms for clinical trials — Measurement of physical properties — Amendment 1 Published By…
-
ISO 16010:2005
Elastomeric seals — Material requirements for seals used in pipes and fittings carrying gaseous fuels…
-
ISO 16020:2005
Steel for the reinforcement and prestressing of concrete — Vocabulary Published By Publication Date Number…
-
ISO 16035:2003
Animal and vegetable fats and oils — Determination of low-boiling halogenated hydrocarbons in edible oils…
-
BS ISO 16020:2005:2006 Edition
Steel for the reinforcement and prestressing of concrete. Vocabulary Published By Publication Date Number of…
-
ISO 16000-18:2011
Air intérieur — Partie 18: Détection et dénombrement des moisissures — Échantillonnage par impaction Published…
-
ISO 16000-6:2021
Indoor air — Part 6: Determination of organic compounds (VVOC, VOC, SVOC) in indoor and…
-
ISO 16031-2:2003
Systèmes aérospatiaux de fluides — Joints toriques, série en inches: diamètres intérieurs et sections, tolérances…
-
ISO 16031-1:2002
Systèmes aérospatiaux de fluides — Joints toriques, série en inches: diamètres intérieurs et sections, tolérances…
-
ISO 16630:2009
Metallic materials — Sheet and strip — Hole expanding test Published By Publication Date Number…
-
ISO 14030-4:2021
Environmental performance evaluation – Green debt instruments – Part 4: Verification programme requirements Published By…
-
ISO/TR 16060:2003
Destructive tests on welds in metallic materials — Etchants for macroscopic and microscopic examination Published…
-
ISO/IEC 17030:2021
Évaluation de la conformité — Exigences générales pour les marques de conformité par tierce partie…
-
ISO 16000-24:2009
Indoor air — Part 24: Performance test for evaluating the reduction of volatile organic compound…
-
ISO 16000-11:2006
Indoor air — Part 11: Determination of the emission of volatile organic compounds from building…
-
ISO 16330:2003
Reciprocating positive displacement pumps and pump units — Technical requirements Published By Publication Date Number…
-
ISO 16038:2005
Rubber condoms — Guidance on the use of ISO 4074 in the quality management of…
-
ISO 16034:2002
Ophthalmic optics — Specifications for single-vision ready-to-wear near- vision spectacles Published By Publication Date Number…
-
ISO 16000-14:2009
Indoor air — Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs)…
-
ISO 16030:2001/Amd 1:2005
Pneumatic fluid power — Connections — Ports and stud ends — Amendment 1 Published By…
-
ISO 16037:2002
Préservatifs masculins en caoutchouc destinés aux essais cliniques — Mesurage des propriétés physiques Published By…
-
ISO 16000-1:2004
Indoor air — Part 1: General aspects of sampling strategy Published By Publication Date Number…
-
ISO 16000-17:2008
Air intérieur — Partie 17: Détection et dénombrement des moisissures — Méthode par culture Published…
-
ISO 16000-13:2008
Indoor air — Part 13: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs)…
-
ISO 16070:2005
Petroleum and natural gas industries — Downhole equipment — Lock mandrels and landing nipples Published…
-
ISO 16730:2008
Fire safety engineering — Assessment, verification and validation of calculation methods Published By Publication Date…
-
ISO/IEC 17030:2003
Conformity assessment — General requirements for third-party marks of conformity Published By Publication Date Number…
-
AS/NZS ISO 16034:2011
Ophthalmic optics – Specifications for single-vision ready-to-wear near-vision spectacles Published By Publication Date Number of…
-
ISO 16000-6:2011
Indoor air — Part 6: Determination of volatile organic compounds in indoor and test chamber…
-
ISO 16032:2004
Acoustics — Measurement of sound pressure level from service equipment in buildings — Engineering method…
-
AS ISO 16003:2010
Components for fire extinguishing systems using gas – Requirements and test methods – Container valve…
-
ISO 16000-23:2009
Indoor air — Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by…
-
ISO 16000-9:2006
Air intérieur — Partie 9: Dosage de l’émission de composés organiques volatils de produits de…
-
ISO 16003:2008
Components for fire-extinguishing systems using gas— Requirements and test methods — Container valve assemblies and…
-
ISO 16039:2004
Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications Published By…
