BS EN 13265:2016 – TC:2020 Edition
$246.62
Tracked Changes. Geotextiles and geotextile-related products. Characteristics required for use in liquid waste containment projects
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 93 |
This European Standard specifies the relevant characteristics of geotextiles and geotextile-related products used in liquid waste containment projects, and the appropriate test methods to determine these characteristics. The intended use of these geotextiles or geotextile-related products is to fulfil one or more of the following functions: filtration, reinforcement and protection. This European Standard is not applicable to geosynthetic barriers, as defined in EN ISO 10318 1. This European Standard provides for the assessment and verification of constancy of performance of the product to this European Standard and for factory production control procedures. Particular application cases may contain requirements regarding additional properties and – preferably standardized – test methods, if they are technically relevant. This European Standard may be used to derive design values by taking into account factors within the context of the definitions given in EN 1997 1 (Eurocode 7), e.g. factors of safety. The design life of the product should be determined, since its function may be temporary, as a construction expediency, or permanent, for the lifetime of the structure.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 51 | Contents Page |
| 53 | European foreword |
| 54 | Introduction |
| 55 | 1 Scope 2 Normative references |
| 56 | 3 Terms, definitions and abbreviations 3.1 Terms and definitions |
| 57 | 3.2 Abbreviations 4 Required characteristics and corresponding methods of test 4.1 General 4.2 Selection of the appropriate standard in a specific application |
| 58 | Table 1 — Geotextiles and geotextile-related products used in liquid waste containment projects – Functions, function-related characteristics and test methods to be used |
| 60 | 4.3 Characteristics relevant to specific conditions of use 4.3.1 Stiffness at 2 %, 5 % and 10 % 4.3.2 Tensile strength of seams and joints 4.3.3 Static puncture 4.3.4 Friction characteristics 4.3.5 Tensile creep 4.3.6 Resistance to damage during installation 4.3.7 Water permeability normal to the plane 4.4 Release of dangerous substances |
| 61 | 5 Assessment and verification of constancy of performance (AVCP) 5.1 General 5.2 Presentation of characteristics 5.3 Product type determination (PTD) Table 2 — Characteristics required for PTD and AVCP |
| 62 | 5.4 Factory production control (FPC) 5.5 Verification of values 5.6 Initial inspection of factory and of FPC |
| 63 | 5.7 Continuous surveillance of FPC 6 Marking |
| 64 | Annex A (normative) Factory production control A.1 Factory production control scheme A.1.1 General A.1.2 Product design A.1.3 Production A.1.3.1 Raw or incoming materials A.1.3.2 Production process A.1.4 Finished products A.1.4.1 Tests on the finished product A.1.4.2 Alternative tests |
| 65 | A.1.4.3 Equipment A.1.5 Provisions applicable to A.1.2, A.1.3 and A.1.4 (to be used where appropriate) A.1.5.1 Records A.1.5.2 Assessment of results A.1.5.3 Traceability A.1.5.4 Corrective action for non-conforming materials and products A.1.5.5 Personnel A.1.5.6 Quality management |
| 66 | A.2 Assessment of a factory production control (FPC) system A.2.1 General A.2.2 Checklist Table A.1 — Checklist for FPC |
| 70 | A.2.3 Test frequency Table A.2 — Minimum test frequency required for FPC |
| 71 | Annex B (normative) Durability aspects B.1 General B.1.1 Service life B.1.2 Initial and repeat testing of durability |
| 72 | B.1.3 Use of rework material B.2 Weathering (all products) Table B.1 — Maximum exposure times B.3 Products used in non-reinforcing applications and with service lives up to 5 years |
| 73 | B.4 Other applications and service lives up to 25 years, 50 years and 100 years B.4.1 General B.4.2 Tests for specific materials B.4.2.1 Polyester (PET) |
| 74 | B.4.2.2 Polypropylene (PP) and Polyethylene (PE) B.4.2.3 Polyamide (PA) and aramid (AR) B.4.2.3.1 Oxidation resistance |
| 75 | B.4.2.3.2 Hydrolysis resistance B.4.2.4 Polyvinyl alcohol (PVA) B.4.2.4.1 Oxidation resistance for PTD |
| 76 | B.4.2.4.2 Oxidation resistance follow up procedure |
| 77 | Annex C (informative) Guidelines for the selection of the appropriate standard in a specific application |
| 78 | Table C.1 — Selection of the appropriate standard |
| 79 | Annex D (informative) Significant technical changes to the superseded standard |
| 80 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation ZA.1 Scope and relevant characteristics Table ZA.1.1 — Relevant clauses for geotextiles and geotextile-related products – Filtration |
| 81 | Table ZA.1.2 — Relevant clauses for geotextiles and geotextile-related products – Reinforcement Table ZA.1.3 — Relevant clauses for geotextiles and geotextile-related products – Protection |
| 82 | Table ZA.1.4 — Relevant clauses for geotextiles and geotextile-related products – Filtration and reinforcement |
| 83 | Table ZA.1.5 — Relevant clauses for geotextiles and geotextile-related products – Reinforcement and protection ZA.2 Procedure for AVCP of Geotextiles and geotextiles-related products for the use in the construction of liquid waste containment projects ZA.2.1 Systems of AVCP |
| 84 | Table ZA.2 — Systems of AVCP |
| 85 | Table ZA.3.1 — Assignation of evaluation of conformity tasks for geotextiles and geotextile-related products for use in liquid waste containment projects under system 2+ |
| 86 | ZA.2.2 Declaration of performance (DoP) ZA.2.2.1 General ZA.2.2.2 Content |
| 87 | ZA.2.2.3 Example of DoP |
| 90 | ZA.3 CE marking and labelling |
| 91 | Bibliography |
