🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 1143-2:2014

BS EN 1143-2:2014

$198.66

Secure storage units. Requirements, classification and methods of tests for resistance to burglary – Deposit systems

Published By Publication Date Number of Pages
BSI 2014 54
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This European Standard specifies requirements and tests methods for deposit systems, and classifies the systems according to their burglary resistance and their resistance to the theft of deposits.

This European Standard comprises two types of deposit system:

  • Night safes which provide depositing services for the customers of financial institutions without giving access to the content of the night safe.

  • Deposit safes which enable the personnel of a company to place money or valuables in safe custody without giving access to the content of the deposit safe. The installation condition for deposit safe according to this European Standard is that the depositing functions are installed inside the premises of the company and are only disposable for the personnel of the company.

NOTE Parts of a deposit system are a receiving unit, an input unit and in some cases, a chute.

This European Standard includes design requirements for deposit systems controlled by programmable controllers and for the software for these. Controller hardware testing is restricted to mechanical or electromechanical attacks of electric motors, sensors, coils and similar devices; but software testing as attempts to influence controller software or controller hardware is not part of this standard.

Deposit systems may have devices for functions such as user identification and/or counting and registration of money. Tests of and requirements for classification of such functions are not included.

This European Standard does not cover protection of persons using the deposit system or the prevention of fraud committed by operators of the deposit system.

PDF Catalog

PDF Pages PDF Title
3 CEN/TC 263
4 Contents Page
5 Foreword
7 Introduction
8 1 Scope
2 Normative references
3 Terms and definitions
3.1 Deposit system definitions
10 3.2 Deposit tool attack definitions
11 4 Classification and requirements
4.1 Classification
Table 1 — Possible classifications of deposit systems
4.2 General requirements
4.2.1 Holes in protection material
12 4.2.2 Cable hole
4.2.3 User instructions
4.3 Requirements for receiving units
4.3.1 Dimensions
4.3.2 Boltwork cover plate
4.3.3 Locks: number and class
4.3.4 Partial and complete access
13 4.3.5 Fixing system
Table 2 — Minimum requirements for deposit safe (D) receiving unit
Table 3 — Minimum requirements for night safe (N) receiving unit
4.4 System requirements
4.4.1 General
14 4.4.2 Integrated deposit systems
4.4.3 Distributed deposit systems
4.4.4 Resistance to deposit tool attacks
15 Table 4 — Minimum requirements for deposit tool attacks for deposit safe (D)
Table 5 — Minimum requirements for deposit tool attacks for night safe (N)
5 Technical documentation
17 6 Test specimen
18 7 Test program
Table 6 — Summary of tests that shall be performed on all deposit systems in all applicable grades
19 Table 7 — Summary of tests that shall be performed on night safes in all grades
Table 8 — Summary of tests that shall be performed on deposit systems with optional requirement in applicable grades
20 8 Tool attack tests
8.1 General
8.2 Principle
8.3 Testing team
8.4 Apparatus
8.4.1 Attack tools
21 8.4.2 Clock
8.5 General test conditions
22 8.6 General test procedure
8.6.1 Preparations of final test program
8.6.2 Attack tools for each test
8.6.3 Status and position of the test specimen
8.6.4 Measurement of operating time
23 8.7 Calculation of resistance values
24 8.8 Test record – tool attack tests
25 9 Access tool attack tests
9.1 Partial access – tool attack test
9.1.1 General
9.1.2 Test blocks to measure partial access
9.1.3 Test criteria
9.2 Complete access – tool attack test
9.2.1 General
26 9.2.2 Test blocks to measure complete access
9.2.3 Test criteria
9.3 Partial access EX – explosive tool attack test
9.3.1 Principle
9.3.2 Test specimen
27 9.3.3 Explosives
9.3.4 Plastic explosive charge mass
Table 9 — Mass of plastic explosive charge
9.3.5 Test criteria
9.3.6 Attack tool restrictions for post-detonation tool attack
9.3.7 Elements to be attacked
9.3.8 Test procedure
9.3.9 Test record
28 9.4 Partial access GAS – explosive tool attack test
9.4.1 Principle
9.4.2 Test specimen
9.4.3 Explosives
9.4.4 Explosive charge volume
9.4.5 Test equipment
29 9.4.6 Test criteria
9.4.7 Attack tool restrictions for post-detonation tool attack
9.4.8 Test procedure
9.4.9 Test record
10 Deposit tool attack tests (removal of deposits)
30 10.1 General for all deposit tool attack tests
10.1.1 Purpose and general
10.1.2 Attack tool restrictions and additions
10.1.3 Preparations of the deposit system before testing
31 10.1.4 Test conditions
10.1.5 Criteria for fulfilled test and status of deposits
10.2 Test conditions for Deposit forcing tool attack test
10.2.1 Code or key to the input unit
10.2.2 Place from where deposits shall be removed
10.2.3 Elements to be attacked
10.2.4 Way out for the deposits
10.2.5 Damages, changes, traces
32 10.2.6 Criteria for fulfilled test, number of removed deposits
10.3 Test conditions for Deposit forcing EX tool attack test
10.3.1 Principal
10.3.2 Code or key to the input unit
10.3.3 Explosives and charge mass
10.3.4 Place from where deposits shall be removed
10.3.5 Placing and tamping the plastic explosive charge
33 10.3.6 Post-detonation tool attack (remaining resistance value)
10.3.6.1 Operation time for Post-detonation tool attack
10.3.6.2 Elements to be attacked during post-detonation tool attack
10.3.6.3 Way out for the deposits
10.3.6.4 Damages, changes, traces
10.3.6.5 Criteria for fulfilled test, number of deposits
10.3.7 Test record
10.4 Test conditions for Deposit forcing GAS tool attack test
10.4.1 Principal
10.4.2 Code or key to the input unit
34 10.4.3 Explosives
10.4.4 Explosive charge volume
10.4.5 Place from where deposits shall be removed
10.4.6 Test procedure
10.4.7 Post-detonation tool attack (remaining resistance value)
10.4.7.1 General
10.4.7.2 Operation time for Post-detonation tool attack
10.4.7.3 Elements to be attacked during post-detonation tool attack
35 10.4.7.4 Way out for the deposits
10.4.7.5 Damages, changes, traces
10.4.7.6 Criteria for fulfilled test, number of deposits
10.4.8 Test record
10.5 Test conditions for Deposit fishing tool attack test
10.5.1 Code or key to the input unit
10.5.2 Place from where deposits shall be removed
10.5.3 Elements to be attacked
10.5.4 Way out for the deposits
10.5.5 Damages, changes, traces
36 10.5.6 Criteria for fulfilled test, number of deposits
10.6 Test conditions for Deposit retrieval tool attack test
10.6.1 Code or key to the input unit
10.6.2 Place from where deposit shall be removed
10.6.3 Elements to be attacked
10.6.4 Way out for the deposit
10.6.5 Damages, changes, traces
10.6.6 Criteria for fulfilled test, number of deposits
10.7 Test conditions for Last deposit trapping tool attack test
10.7.1 Code or key to the input unit
10.7.2 Additional attack tools, devices
37 10.7.3 Interruptions for depositing
10.7.4 Place from where the deposit shall be removed
10.7.5 Elements to be attacked
10.7.6 Way out for the deposit
10.7.7 Damages, changes, traces
10.7.8 Criteria for fulfilled test, number of deposits
10.8 Test conditions for Deposit repeated trapping tool attack test
10.8.1 Code or key to the input unit
10.8.2 Additional attack tools, devices
10.8.3 Interruptions for depositing
38 10.8.4 Place from where deposits shall be removed
10.8.5 Elements to be attacked
10.8.6 Way out for the deposits
10.8.7 Damages, changes, traces
10.8.8 Criteria for fulfilled test, number deposits
11 Fixing system tool attack tests
11.1 Fixing system – tool attack test without force
11.1.1 Principle
11.1.2 Test specimen
11.1.3 Equipment
39 11.1.4 Elements to be attacked
11.1.5 Test criteria
11.1.6 Preparation
11.1.7 Attack tool restrictions
11.1.8 Test record
11.2 Fixing system – tool attack test with force
11.2.1 Principle
40 11.2.2 Test specimen
11.2.3 Equipment
11.2.4 Attack tool restrictions
11.2.5 Test criteria
11.2.6 Preparation
41 11.2.7 Test procedure
11.2.7.1 Removing or weakening of external fixings
11.2.7.2 Force
Figure 1 — Testing arrangements for applying the force
42 11.2.7.3 Tool attack test on the fixing attachments
11.2.8 Test record
12 Test report and test records
12.1 Test report
43 12.2 Test records
13 Marking
44 Annex A (informative) Examples of different design of deposit systems
Figure A.1 — Designs of deposit systems
45 Annex B (informative) Examples of integrated and distributed deposit system
B.1 Integrated deposit system
Figure B.1 — Example of integrated deposit system
46 B.2 Different distributed deposit systems
Figure B.2 — Example of distributed deposit system without remote access
47 Figure B.3 — Example of distributed deposit system without remote access
48 Figure B.4 — Example of distributed deposit system with external user interface for local authorization option 1
49 Figure B.5 — Example of distributed deposit system with external user interface for local authorization option 2
50 Annex C (informative) Additional tools for deposit tool attack tests
Table C.1 — Additional tools for deposit tool attack tests (manipulation and fishing devices)
52 Annex D (informative) Structure of test clauses
Table D.1 — Structure of test clauses in EN 1143–2

Related products

BS EN 1143-2:2014
$198.66