šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN 10209:2023 – TC

BS EN 10209:2023 – TC

$186.33

Tracked Changes. Cold rolled low carbon steel flat products for vitreous enamelling. Technical delivery conditions

Published By Publication Date Number of Pages
BSI 2023 70
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

This document applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) or to cold rolled flat products for which there is a specific standard, in particular the following: – cold-rolled low carbon steel flat products for cold forming (EN 10130); – cold-rolled non-oriented electrical steel sheet and strip delivered in fully processed state (EN 10106); – cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); – cold reduced blackplate (EN 10205); – steel sheet and strip for welded gas cylinders (EN 10120); – cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139); – cold-rolled structural steels for general purposes; – cold-rolled flat products made of high yield strength for cold forming (EN 10268).

PDF Catalog

PDF Pages PDF Title
1 30477673
41 A-30453293
42 undefined
47 1 Scope
2 Normative references
48 3 Terms and definitions
4 Designation
5 Requirements
5.1 Steelmaking and manufacturing processes
5.2 Method of deoxidation
49 5.3 Chemical composition
5.4 Suitability for vitreous enamelling
5.5 Delivery condition
50 5.6 Choice of properties
5.7 Mechanical properties
5.8 Surface characteristics
5.8.1 General
5.8.2 Surface appearance
5.8.3 Surface finish
51 5.9 Stretcher strain marks
5.10 Weldability
5.11 Tolerances on dimensions and shape
6 Tests
6.1 General
6.2 Inspection units
6.3 Number of tests
6.4 Sampling
52 6.5 Test methods
6.6 Retests
6.7 Inspection documents
7 Identification
8 Packaging
53 9 Disputes
10 Information to be supplied by the purchaser at the time of ordering
55 Annex A (normative)Methods for determining the resistance to fish scaling of a steel sheet for enamelling
A.1 Hydrogen permeation test
A.1.1 Field of application
A.1.2 Principle
A.1.3 Apparatus
A.1.4 Sampling
A.1.5 Preparation
56 A.1.6 Check the degreasing quality
A.1.6.1 General
A.1.6.2 Method A
A.1.6.3 Method B
A.1.7 Permeation test procedure
A.1.8 Hydrogen detection
A.1.8.1 E. Buchel and L. Leontaritis measuring apparatus
A.1.8.2 Apparatus with hydrogen sensor
57 A.1.8.3 Evaluating the results
A.1.9 Evaluation
58 A.2 Fish scaling test using special enamel
59 Annex B (normative)Method for determining mass loss (iron loss) due to pickling for steel grades for direct enamelling in accordance with 5.4.2
B.1 Principle
B.2 Apparatus
B.3 Sampling
60 B.4 Preparation
B.5 Weighing
B.6 Cleaning
B.7 Checks on degreasing quality
B.8 Pickling
61 B.9 Drying
B.10 Weighing after cooling
B.11 Evaluation
62 Annex C (normative)Method for determining the adherence level of enamel applied to a steel sheet
C.1 Field of application
C.2 Principle
C.3 Apparatus
C.4 Description of the apparatus
C.5 Procedure
63 C.6 Adherence level evaluation
C.6.1 Flat pieces
C.6.2 Thinner sheet steel < 0,3 mm
C.6.3 Deformed pieces
67 Annex D (informative)Characteristics for the selection of enamelling steel grades

Related products

BS EN 10209:2023 - TC
$186.33