ASTM-A1035:2013 Edition(Redline)

$26.65

A1035/A1035M-13 Standard Specification for Deformed and Plain, Low-carbon, Chromium, Steel Bars for Concrete Reinforcement (Redline)

Published By	Publication Date	Number of Pages
ASTM	2013	8

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification covers low-carbon, chromium, steel bars, deformed and plane for concrete reinforcement in cut lengths and coils. The bars shall be rolled from properly identified heats of mold cast or strand cast steel using the basic oxygen, electric-furnace, or open-hearth process. Heat analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, chromium, manganese, nitrogen, phosphorus, sulfur, and silicon. Steel specimens shall also undergo deformations test, tensile test, and bend test. Steel specimens shall conform to required values of tensile strength, yield strength, stress, and elongation. Final products shall be marked by a tag.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers low-carbon, chromium, steel bars, deformed and plain for concrete reinforcement in cut lengths and coils. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1 . The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. ²

TABLE 1 Deformed Bar Designation Numbers, Nominal Weights [Masses], Nominal Dimensions, and Deformation Requirements

^A The nominal dimensions of a deformed bar are equivalent to those of a plain round bar having the same weight [mass] per foot [metre] as the deformed bar.

1.2 Bars are of two minimum yield strength levels as defined in 9.2 : namely, 100 000 psi [690 MPa], and 120 000 [830 MPa] designated as Grade 100 [690] and Grade 120 [830], respectively.

Note 1 — Caution: Designers need to be aware that typical design standards limit the design strength to 80 000 psi [550 MPa], except for prestressing steel and for spiral transverse reinforcement. Members reinforced with bars with yield strengths that are considerably above 80 000 psi [550 MPa] may exhibit behavior that differs from that expected of conventional reinforced concrete members or may require special detailing to ensure adequate performance at service and factored loads.

1.3 Deformed bars shall have a minimum yield strength and other tensile properties in accordance with Table 2 . Hot-rolled plain rounds in sizes up to and including 2.25 in. [57.2 mm] in diameter in coils or cut lengths when specified for dowels, spirals, structural ties or bar supports shall be furnished under this specification and shall also meet the tensile properties requirements of Table 2 . Ductility properties for plain rounds shall be those of the nearest smaller nominal diameter deformed bar size in Table 2 . Requirements covering deformation dimensions and marking are not applicable to plain rounds.

TABLE 2 Tensile Properties Requirements

Note 2 — Welding of the material in this specification should be approached with caution since no specific provisions have been included to enhance its weldability. When this steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used.

1.4 Requirements for alternate bar sizes are presented in Annex A1 . The requirements in Annex A1 only apply when specified by the purchaser (see 4.1.10 ).

1.5 This specification is applicable for orders in either inch-pound units (as Specification A1035) or in SI units (as Specification A1035M).

1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

A370 Test Methods and Definitions for Mechanical Testing of Steel Products

A510 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

A510M Specification for Genera

Additional information

14 [43]	7.65 [11.38 ]
7 [22]	2.044 [ 3.042]
18 [57]	13.60 [20.24 ]
Yield strength (0.2 % offset), min, psi [MPa]	100 000 [ 690]
Diameter, in. [mm]	Cross-Sectional Area, in. 2 [mm 2 ]
4 [13]	0.668 [ 0.994]
14, 18 [43, 57]	6
3 [10]	0.376 [ 0.560]
Elongation in 8 in. [200 mm], min, %:
11 [36]	5.313 [ 7.907]
Stress corresponding to an extension under load of 0.0035 in./in. [0.0035 mm/mm], min, psi [MPa]	80 000 [ 550]
8 [25]	2.670 [ 3.973]
Tensile strength, min, psi [MPa]	150 000 [1030]
6 [19]	1.502 [ 2.235]
5 [16]	1.043 [ 1.552]
3 through 11 [10 through 36]	7
9 [29]	3.400 [ 5.060]
Bar Designation No.
	Grade 100 [690]
10 [32]	4.303 [ 6.404]

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A1035:2013 Edition(Redline)

Related products