IEC 61169-48:2014, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series BMP RF coaxial connectors with blind mating, typically for use in 50 Ohms board to board connection. They may also be used with RF cables or micro-strips in microwave, telecommunication, wireless and other fields. Their operating frequency limit is up to 6 GHz. It describes the interface dimensions with gauging information, electrical and mechanical performance including the mandatory tests selected from IEC 61169-1:2013 applicable to all DS relating to type BMP connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers test schedules and inspection requirements.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 4<\/td>\n | Foreword Endorsement notice <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Annex ZA (normative) Normative references to international publications with their corresponding European publications <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | English CONTENTS <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 1 Scope 2 Normative references 3 Mating face and gauge information 3.1 Dimensions \u2013 General connectors \u2013 Grade 2 3.1.1 Connector with pin-centre contact \u2013 Full detent and smooth bore <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 3.1.2 Connector with socket-centre contact Figures Figure 1 \u2013 Connector with pin-centre contact Tables Table 1 \u2013 Dimensions of connector with pin-centre contact <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 3.2 Gauges 3.2.1 Gauge pin for socket-centre contact Figure 2 \u2013 Connector with socket-centre contact Table 2 \u2013 Dimensions of connector with socket-centre contact <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 3.2.2 Test procedure Figure 3 \u2013 Gauge pin for socket-centre contact Table 3 \u2013 Dimensions of gauge pin for socket-centre contact <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3.2.3 Gauge for outer contact of connector with pin-centre contact Figure 4 \u2013 Gauge A for sizing test Table 4 \u2013 Gauge A for sizing test <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | Figure 5 \u2013 Gauge B for retention test for pin connectors \u2013 Full detent Table 5 \u2013 Gauge B for retention test for pin connectors \u2013 Full detent <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 3.3 Dimensions \u2013 Standard test connectors \u2013 Grade 0 3.3.1 Connector with pin-centre contact Figure 6 \u2013 Gauge C for retention test for pin connectors \u2013 Smooth bore Table 6 \u2013 Gauge C for retention test for pin connectors \u2013 Smooth bore <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 3.3.2 Connector with socket-centre contact Figure 7 \u2013 Connector with pin-centre contact Table 7 \u2013 Dimensions of connector with pin-centre contact <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 3.4 General requirements for connector mounting on PCB 3.4.1 General Figure 8 \u2013 Connector with socket-centre contact Table 8 \u2013 Dimensions of connector with socket-centre contact <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 3.4.2 Maximum permitting deflexion 3.4.3 Maximum permitting axial clearance 4 Quality assessment procedure 4.1 General 4.2 Rating and characteristics (see Clause 5 of IEC\u00a061169-1:2013) Figure 9 \u2013 General requirements for connector mounting on PCB <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Table 9 \u2013 Preferred climatic categories (see IEC\u00a060068-1) Table 10 \u2013 Rating and characteristics <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 4.3 Test schedule and inspection requirements \u2013 Acceptance tests 4.3.1 Acceptance tests <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 4.3.2 Periodic tests Table 11 \u2013 Acceptance tests Table 12 \u2013 Periodic tests <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | 4.4 Procedures for the quality conformance 4.4.1 Quality conformance inspection 4.4.2 Quality conformance and its maintenance \u2013 General procedure 5 Instructions for preparation of detail specifications 5.1 General <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | 5.2 Identification of the component 5.3 Performance 5.4 Marking, ordering information and related matters 5.5 Selection of tests, test conditions and severities <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 5.6 Blank detail specification pro-forma for type BMP connector <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | 6 Marking 6.1 Marking of component 6.2 Marking and contents of package <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Radio-frequency connectors – Sectional specification for series BMP R.F. coaxial connectors<\/b><\/p>\n |