This document specifies the safety and interchangeability requirements together with the test methods and conditions required to show compliance of non-integrated tubular LED lamps, intended for general lighting purposes, having:<\/p>\n
a rated wattage up to 70 W,<\/p>\n<\/li>\n
a rated voltage up to 190 V ripple free DC,<\/p>\n<\/li>\n
GX16t-5 cap as listed in Table 1<\/span>.<\/p>\n<\/li>\n<\/ul>\n The requirements of this document relate only to type testing.<\/p>\n Where in this document the term \u201clamp(s)\u201d is used, it is understood to stand for \u201cnon-integrated GX16t-5 capped tubular LED-lamp(s)\u201d, except where it is obviously assigned to other types of lamps.<\/p>\n<\/div>\n The lamp specified in this document is operated with a controlgear specified in Annex B<\/span>. See Clause 18<\/span>.<\/p>\n<\/div>\n This document includes photobiological safety.<\/p>\n<\/div>\n GX16t-5 capped tubular led lamp. Safety specifications<\/b><\/p>\nPDF Catalog<\/h4>\n
\n
\n PDF Pages<\/th>\n PDF Title<\/th>\n<\/tr>\n \n 2<\/td>\n National foreword <\/td>\n<\/tr>\n \n 5<\/td>\n Annex ZA(normative)Normative references to international publicationswith their corresponding European publications <\/td>\n<\/tr>\n \n 7<\/td>\n English
CONTENTS <\/td>\n<\/tr>\n\n 9<\/td>\n FOREWORD <\/td>\n<\/tr>\n \n 11<\/td>\n 1 Scope
2 Normative references <\/td>\n<\/tr>\n\n 12<\/td>\n 3 Terms and definitions <\/td>\n<\/tr>\n \n 13<\/td>\n 4 General requirements and general test requirements
5 Marking
5.1 Marking on the lamp <\/td>\n<\/tr>\n\n 14<\/td>\n 5.2 Marking on the packing or in instructions
5.3 Durability and legibility of marking
Figures
Figure 1 \u2013 Lamp not suitable for use under dust and moisture <\/td>\n<\/tr>\n\n 15<\/td>\n 6 Interchangeability
6.1 Dimensional requirements of caps
6.2 Mass
6.3 Dimensions
6.3.1 General
6.3.2 Dimensions at 25 \u00b0C (non-operating)
6.3.3 Dimension A at maximum ambient temperature (operating)
Tables
Table 1 \u2013 Sheet references of IEC\u00a060061-1 and IEC 60061-3 <\/td>\n<\/tr>\n\n 16<\/td>\n 6.3.4 Dimension A at minimum ambient temperature (non-operating)
6.4 Temperature
6.5 Lamp bowing (sag) <\/td>\n<\/tr>\n\n 17<\/td>\n 6.6 Pin connection
7 Protection against accidental contact with live parts <\/td>\n<\/tr>\n\n 18<\/td>\n Figure 2 \u2013 Standard test finger (according to IEC\u00a060529) <\/td>\n<\/tr>\n \n 19<\/td>\n 8 Insulation resistance and electric strength after humidity treatment
8.1 General
8.2 Insulation resistance
8.3 Electric strength
9 Mechanical requirements for caps
9.1 General
9.2 Torque test on unused lamps
Table 2 \u2013 Test voltages for caps <\/td>\n<\/tr>\n\n 20<\/td>\n 9.3 Torque test after heat treatment
9.4 Live part accessibility after mechanical tests
10 Cap temperature rise
11 Resistance to heat <\/td>\n<\/tr>\n\n 21<\/td>\n 12 Resistance to flame and ignition
Figure 3 \u2013 Ball-pressure test apparatus <\/td>\n<\/tr>\n\n 22<\/td>\n 13 Resistance to heat of insulating material of cap
14 Fault conditions
14.1 General
14.2 Testing under extreme electrical conditions <\/td>\n<\/tr>\n\n 23<\/td>\n 14.3 Short-circuit across capacitors
14.4 Fault conditions across electronic components
14.5 Compliance
15 Creepage distances and clearances <\/td>\n<\/tr>\n\n 24<\/td>\n 16 Ingress protection
16.1 Aim of the test
16.2 Thermal endurance
16.3 IP testing
17 Photobiological safety
17.1 UV radiation
17.2 Blue light hazard
17.3 Infrared radiation <\/td>\n<\/tr>\n\n 25<\/td>\n 18 Information for controlgear design
19 Information for lampholder design
20 Information for luminaire design <\/td>\n<\/tr>\n\n 26<\/td>\n Annex A (normative) Test method for lamp cap temperature rise for GX16t-5 lamps <\/td>\n<\/tr>\n \n 27<\/td>\n Annex B (informative) Information for controlgear design
B.1 Guidelines for safe lamp operation
B.2 General
B.3 Protection against electric shock
B.3.1 No-load condition
B.3.2 Overload condition, normal condition and short-circuit condition
Table B.1 \u2013 No load output voltage of the controlgear <\/td>\n<\/tr>\n\n 29<\/td>\n Annex C (informative) Information for luminaire design
C.1 General
C.2 Thermal variation of lamp length
C.3 Lampholders <\/td>\n<\/tr>\n\n 30<\/td>\n Annex D (normative) Dimensions and information to electrical characteristics <\/td>\n<\/tr>\n \n 36<\/td>\n Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" \n\n
\n Published By<\/td>\n Publication Date<\/td>\n Number of Pages<\/td>\n<\/tr>\n \n BSI<\/b><\/a><\/td>\n 2017<\/td>\n 38<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":226344,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[521,2641],"product_tag":[],"class_list":{"0":"post-226340","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-29-140-10","7":"product_cat-bsi","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/226340","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/226344"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=226340"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=226340"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=226340"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}